EXTREME HIGH ANGLE 45, 60, 80 CV DRIVE SHAFTS

 

Chevy and Dodge CLICK HERE FOR STOCK SAGINAW FRONT DRIVE SHAFTS

All Vehicles CLICK HERE FOR OTHER HIGH ANGLE CV FRONT DRIVE SHAFTS  FOR VEHICLES THAT DO NOT HAVE SUCH HIGH LIFTS.

Why the  BIG  2 Ton Double Cardan CVs?    CLICK HERE.

QUESTION ON THE MATERIAL BELOW GIVE US A CALL, PLEASE.

Compare the Performer  parts and 1350 parts. Get a relative idea of difference in size and strength

 Center Bearing  Rated 8k rpms     Ball Stud Yokes 3/4" VRS 1/2"                          H - yokes

 

____________________________________________________________________________   Seals Over Bearing No Boots                  Seals Only         We use pressed on seals like the Spicer CVs instead of boots which do the job extremely better than boots.

DAILY DRIVER A PERFORMER CV is used on front or rear of  Fords, Chevy, DODGES, Jeeps, and many others  when lifts are high or  the drive shaft turns all the time.  The flange  on the CV will fit your choice of pilot at the Transfer case.   Long splines is optional for only $75 dollars at the time the drive shaft is purchased. The drive shaft  below has long  splines 9" long double the amount of travel. Tell us what vehicle you want it to fit and we will figure out the yokes it bolt to. 45 degrees max, 35 max operating rated at 2 ton for high speed driving.   No long splines   $595 Driveshaftsuperstore only Item With long splines  $670 We also do the all drive shafts for the rear of a Dodge. OFF-ROAD ONLY  OR FRONT DRIVE SHAFT-For Dodges, Fords, Chevys, Jeeps, Toyotas, Suzukis, you name it.  These can be adapted to any vehicle. Normally used for the front except for rock crawling rigs they use it front and rear.  Tell us what the vehicle is and we will figure out what the yokes it bolts to.  This drive shaft is used on Chevy, Ford, Dodges, Toyotas 13" inch lifts and lower.       60 degrees max. and 35 degrees max operating 2TON CV.     BAD BOY JR 2-ton 60 DEGREE DRIVE SHAFT WITH STANDARD SPLINES--   $495.00 BAD BOY JR 2-ton 60 DEGREE DRIVE SHAFT WITH LONG SPLINES--                     $570.00 Tell us what the vehicle is and we will figure out what it bolts to,     TWO Bad Boy JR 60 degree CV with long  splines like the above   ---$685     OFF-ROAD ONLY  OR FRONT DRIVE SHAFT-For Dodges, Fords, Chevy's, Jeeps, Toyotas, Suzuki's, you name it. The application is the same as the Bad Boy Jr except when high angle exist.  This the ultimate front drive shaft for vehicles 14 inches of lift and higher. 80 max. 45 0perating max. Bad Boy 80 degree CV Drive Shaft with standard splines --- $595 Bad Boy 80 degree CV with long  splines like the above  ---$625 We can put this drive on any vehicle front or rear given the interfaces that the drive shaft bolts up to. Remember: The Bad Boy CVs and PERFORMER CV  require a flange. Some flanges are $85 off the shelf for 32 spline TC output shafts, and $99  if we have to make them to fit other splined shafts. All guaranteed not to break. Look at CUSTOM FLANGES.    If you already have a flange , then we will make the our CVs fit yours fit yours.   Usually, we will know what the connections are by the year and model vehicle you enter on your online order form. TWO CV DRIVE SHAFTS NO PICTURE TWO BAD BOY 80 DEGREES 2-TON CV DRIVE SHAFT -- $785 TWO BAD BOY JR 60 DEGREES 2-TON CV DRIVE SHAFT -- $685 TWO PERFORMERS  45 DEGREES 2-TON CV DAILY DRIVER -- $785 TWO HD 1350 35 DEGREES 1-TON CV DRIVE SHAFT -- $525 TWO HD 1350 REGULAR ANGLE 1 TON CV DRIVE SHAFT-- $475 NO PICTURE TWO HD 1310 HIGH ANGLE 40 DEGREES 1/2 TON -- $395 TWO REGULAR ANGLE HALF TON CV DRIVE SHAFT-- $325 NO PICTURE   TO BUY A DIFFERENTIAL FLANGE GO TO CUSTOM FLANGES.